How to make a conductive glue with your own hands

How to just make a conductive glue with your own hands

Conductive glue

In the event of a breakdown of a household electrical appliance, it is not necessary to immediately take it into repair, because it is often a malfunction to be a loss of contact between the tracks on the board, and it is enough to have a conductive glue at hand. You can buy a ready-made composition in the chain stores without any problems, the choice of the range is quite wide: contacting, Elektone, Lac Elast, etc., but for radio amateurs and those who are often repaired independently, it is preferable to make their desired composition. To do this, it is enough to have a minimum necessary component components and know how to make a conductive glue with your own hands.

Features and properties of conductive adhesive compositions

Glue contacting radioThe basis of such adhesion is the presence of certain components capable of providing the necessary level of electricity. These include conventional graphite, nickel powder, polymers, silver powder - suitable small powder of any of the conductive metals.

The adhesive mixture should be elastic, and at the same time, have a slight resistivity. Elasticity will provide point applying of glue and will not allow it to spread over the surface. In this matter, the main thing is to withstand the necessary relationship between powder electrically conductive fillers and polymeric binders. A large number of additives capable of conducting a current can lead to a decrease in the adhesion qualities with various surfaces, which will affect the reliability and strength of contacts.

Electrically conductive glue

The next feature important to work will be the time required to dry the prepared mixture. The faster the glue dries - the better and more convenient for the work of the wizard. To do this, with independent manufacture of the adhesive mixture, any ready-hanging glue or conductive varnish are used. Due to the fact that the microchips during operation are heated, the glue must be heat-resistant and necessarily safe for the working master and others.

Independent manufacture of graphite dust glue

One of the most affordable and common ways is to use graphite dust as conductor. For the preparation of conductive adhesive, you will need only two components of the component - the graphite and the binder in the form of any quick-drying glue or varnish. Prepare a graphite powder is easy, a construction or ordinary pencil core is perfect for this purpose. Grimitel, with the help of a stationery knife, it is necessary to remove and be lost in fine powder.

Independent manufacture of conductive glue

When using the finished glue, the lower part of the tube gently unfolds and a graphite powder can be added to the resulting opening in the one to one ratio. Mix mix well, using toothpick or any other convenient item. After that, the foil of the bottom of the tube turns back and independently manufactured the electrically conductive composition is ready for use by intended purpose. The advantage of the composition prepared on a graphite basis will be rapid drying time.

In addition to the pencil, a worn copper brushes or a coal rod made of salt batteries can be used to prepare a grate powder. It is possible to crush graphite with shallow emery paper or the appliance. It is also important to remember that when used as a binding element of varnish - the reliability of the compound will be lower than when using the finished adhesive composition. With the addition of copper powder, electrical conductivity is significantly increased.

The scope of applying self-cooked electrically conductive composition is quite extensive. For example, glue Universal current wire restores the paths of the remote control panel, computer keyboard - wherever there is no possibility of using the soldering iron. It is often used by car enthusiasts, if necessary, restoring the contacts of the heating of the rear window.

How to make electrically conductive glue from the pencil from the pencil is shown in this video:

Additional recipes

Graphite dust is not the only component that can be used to prepare conductive adhesive compositions. There are some more more complex mixtures that differ in better electrical conductivity or adhesive properties:

  1. A mixture of silver powder (130 g) and graphite (12 g) is conductive components, and the binders are nitrocelulose (8 g), acetone (50 g) and rosin (3 g). In the above order, everything is mixed into the mortar to the state of homogeneous mass and the glue is ready. If glue will thicken, then it must be diluted with acetone. This composition is more designed as a conductive - you should not count that it will hold any details like glue.
  2. Graphite (30 g) and silver (70 g) powder, acetone (70 ml) and vinyl chloride-vinyl acetate (60 g) - after stirring become a syrup-shaped conductive fluid with adhesive properties. Store follows in hermetic dishes so that acetone does not destroy. They also dilute the mixture if it thickens.
  3. The powder made of graphite rod of the finger battery and the chaleon is mixed to obtain a creamy mixture.

What conclusions

Of course, there are other recipes of homemade glue, and above are only the simplest and most common. Whatever the recipe is used, the main thing is that the glue prepared by you, or the glue acquired in the store has to have a minimal resistance. And as any other, such glue should provide a solid, reliable and durable connection.

Many radio amateurs at least once in their lives came across the need to buy connecting compositions that conduct electric current. We propose to consider how to make a conductive glue with your own hands, its properties, as well as the most popular brands and their cost.

What is the glue conducting the current

Glue is a viscous substance that is used to connect a variety of materials. There are so many types of adhesives, each of them has its own characteristics and properties. Among the most popular can be allocated to the stationery (PVC for papers), linoletic (for flooring), conductive (for various electrical circuits and mechanisms).

Conductive glue
Photo - Conducting Glue

Conductive two-component glue must have the following features:

  1. Quickly dry, it is necessary for speed;
  2. To have a viscous consistency to parts of the scheme that do not need to glue are not affected during the processing process;
  3. Have high high-clutch indicators and resistance;
  4. If you want to use the composition for soldering, the glue must be chosen by heat-resistant;
  5. Being safe for the environment and workers.

This substance is necessary for the repair of electrical circuits (keyboard, consumer electronics), the construction of various heating mechanisms, floor coatings (warm floor, tiles, glass), etc.

Elast
Photo - Elast

You can buy a conductive glue without problems in any construction or electrical store, the average price is from 100 rubles per 25 grams. At the same time, considering the flow, we see the following picture:

  1. For PVC coatings, consumption is approximately 250 grams per square meter;
  2. Not PVC (textiles, metal) - 400 grams.

Significantly cheaper to prepare a conductive glue yourself, especially since the components can be bought in any radiotechnical store. Consider the most popular recipes.

How to make conductive homemade glue

Very common method where graphite Plays a major role. You need to buy the cheapest quick-drying glue ("moment", "elephant", "second") or varnish. Caution from the back side of the tube to promote foil, do not damage the seal on the lid. Now we need a soft pencil M4 or M2. From the pencil, we get a griffel, it is pretty kneading to the consistency of the powder and fall asleep into a tube with glue. Long match you need to mix our composition and tighten the foil, be sure to fix it below the pliers so that in the process of operation the adhesive is not a bit. Graphite compounds are mainly dignity - they will quickly dry, but are not suitable for non-ferrous metal on which there is paint. The griffel has a black color, the glue is soluble and will become grayish - traces will remain on the treated surface.

Graphite conductive glue
Photo - Graphite Conductive Glue

You can make homemade not transparent glue on silver - here you need to tinker a little. First you need to buy nitric acid silver or nitric acid . We also need a 1% solution of formalin and ammonia alcohol (ammonia). We combine nitric acid silver with formalin in equal parts and add a few drops of 5% ammonia alcohol. If everything is done correctly, the precipitate will appear - black silver powder, it must be removed from the liquid using the filter and distilled water. Next, they dry the substance at a temperature of 105 to 150 degrees Celsius. We have a black powder to be added to the glue. Many masters recommend to dissolve a little alcohol in Clee before starting work than to make it a little less. The composition will dry very quickly, so mix it periodically.

Another way to obtain the same powder is to evaporate the composition before the appearance of crystals, and after heating them for half an hour at a temperature of up to 400 degrees. As soon as the substance stops bubble - the basis for conductive glue is ready. In fact, it is a fairly effective composition, but it is possible to make it yourself either having a chemist work skills, or if at home you have a mini-laboratory.

Video: overview of conductive adhesives contacting

Professional compounds

Of course, household glue and professional will be varied in quality indicators: it will always be necessary to choose between the speed of frozen, adhesive ability and conductivity. It is much more profitable to buy ready-made conductive glue for loops, linoleum, car, etc.

Consider the most popular stamps:

Mark. Characteristics
Permatex. It is used to repair the filaments of the heat in cars, now it can be bought only from the manufacturer and official dealers. Quickly dries, well grips.
DoneDeal Also necessary for repairing means of movement. The Done Deal kit is two syringe, in one is glue, and in the other - a conductive composition.
FORBO 615 EUROSTAR LINO EL The conductive composition is used for gluing linoleum, carpet and other textile flooring, spent well, almost odor.
Homakoll. Very popular antistatic glue. Perfectly proven itself as a connector for server rooms, health bodies, etc.
TPK-E. We are necessary for gluing stainless steel, heat-resistant, operating temperatures are in the interval from Ma 190 to plus 200.
Elekont Another epoxy adhesive for motorists is not always effective, many masters note that when working with him everything needs to be redone twice.
Contactol-A. The most famous conductive composition. It is very elastic, quickly dries, manufactured on silver, provides reliable installation.
Contact
Photo - contact

Price overview

How much does the conductive adhesive contact in Keller in different cities of Russia, Belarus and Ukraine:

City Price per 100 grams (approximate)
Vladikavkaz 155.
Yekaterinburg 150.
Kiev 145.
Krasnodar 160.
Krasnoyarsk 166.
Minsk 158.
Moscow 150.
Omsk 170.
Samara 175.
Kharkov 156.
St. Petersburg 160.

Before buying, be sure to check the seller's certificate, it is very important, otherwise you can buy a fake.

Application

https://youtube.com/watch?v=u2YLW5Ru0fu.

Before you begin to apply a conductive varnish, the container with it is necessary to shake well. The processed surface should be pre-cleaned by contaminants, such as dirt, dust, fat and moisture. Varnish should be applied only on a dry and clean base. The lacquer is applied with a small layer, you need to work promptly and neatly. After surface treatment, the container with varnish must be sealed, and if a solution was used in a balloon, then you need to carefully clean the valve, then close the can with a lid.

Varieties of conductive glue, adhesive composition characteristics

The basis of the adhesive is the polymer (synthetic resin), on which the viscosity depends. What it is higher, the better the glue is connected to the surface being processed. Conductor current is finely dipped to the powder state of metal (gold, silver, nickel, halflands). To improve the properties and increasing adhesiveness, the filler is treated with synthetic fatty acids, which improves its activity 10 times. Depending on the components with the ability to conduct the current, the glue is divided into the following types:

  1. Based on silver. The basis of the adhesive is synthetic resin (polyester, phenol formaldehyde, polyurethane, epoxy, silicone), providing low viscosity and elasticity. It is added to her fine powder from silver 999 samples, the specific mass of which is several times higher than the amount of polymer resin. This low-toxic remedy does not change its properties even at a temperature of 110c, perfectly isolating and delaying heat or cold. Has a specific resistance from 0.5-0.8 Ohm / cm. It is used in radio devices, to create electrical conductivity on dielectric panels. This is the most expensive, but effective glue.
  2. Based on gold. Such an expensive conductor is needed in the event that an acid affects the instrument or power supply during operation. Glue with fine gold has the highest electrical conductivity, but its value is much higher than silver-based analogues or nickel.
  3. Based on graphite. It is low-cost glue with low current. It has lower high-quality characteristics than a means based on silver or gold, but more accessible in price. It is often used to connect the threads of the rear window of the auto, where a large amount of glue is required. The basis is a copolymer consisting of vinyl acetate, which includes graphite with a property to skip the current. It has a specific resistance from 5 × 10-3 Ohm / m.

Polymeric binders increase adhesiveness of glue, i.e. Its ability to firmly fasten with various surfaces. High elasticity does not give it to spread over the surface. If it is necessary to increase the viscosity of the glue, you need to give it to settle. Particles of metal filler will fall, and the exhaust adhesive base is removed from above. The adhesion suffers from this procedure. Also, polymers make it possible to withstand temperature differences, vibration, blows, so glue is used when repairing electric electricians.

Regardless of the active filler, all conductive adhesives have a low thermal conductivity. This means the temperature difference at the border between the glued surfaces. If it is undesirable, certain components add to the glue. The highest thermal conductivity in copper, it is 0.940 × 10-5 W / cm, but the most common filler is beryllium oxide (0.142 × 10-5 W / cm). The lowest thermal conductivity of asbestos (0.0008 × 10-5 W / cm) and titanium dioxide (0.014 × 10-5 W / cm).

Equipment repair facilities

All devices running from electric current have one big drawback: the ability to fail. And here you have to contact the specialists of different levels: ranging from professional electronics to homegrown radio amateurs.

Their field of activity implies repair and adjustment of the equipment of the extremely wide spectrum. And if in one case you can do well with the standard and habitual means, then in others you have to find more rational and cunning approaches for the qualitative restoration of the workability of the facility of the equipment.

One of these means is conductive glue, or conductive varnish. After all, due to them, the repair of complex radio-electronic equipment becomes much easier, and sometimes it is at all the only possible.

Types of glue "Contactol"

Electrically conductive glue Contactol (Kontaktol) is the products of the famous concern Keller (Germany). The manufacturer offers the following modifications:

  • "On silver" - one-component composition based on purified silver to create electrically conductive tracks on textolite and other solid substrates;
  • Glue "Radio" is created with a graphite filler, therefore it is cheaper, compared with the previous version;
  • The adhesive marker is made of silver powder with PVC filler - such a solution simplifies the treatment of the reducing agent in difficult working conditions.

For your information. Adhesive contact with electrical wires after frozen creates a "track" resistant to moisture. Standard container - 2, 5 and 10 g. Specific resistance - 0.01 Ohm per cc.

Making a conductive glue at home

High cost and high consumption of industrial adhesive substances often makes thinking about how to make a conductive glue with your own hands.

The easiest way is the enrichment of the usual adhesive composition with an electrically conductive component, metallic or hydrocarbon so that electrically conductive glue. For this purpose, you can use any means based on cyanoacrylate. A graphite powder is used as a component that provides electrical conductivity. The substance is easy to prepare a simple pencil from the stylus, which must be missed to the desired consistency.

Look at the video to find out how to make glue yourself:

https://youtube.com/watch?v=zzakl73vbu0.

The volumes of glue and graphite powder must be equal. For ease of operation of the substance, the components can be connected directly in the tube, spinning the lower part of the package. Graphite and glue must be neatly mixed to homogeneity using a wooden or glass wand. This homemade conductive glue differs little on its qualities from factory, especially in the application for repairing the heating of automotive glass.

The adhesive base can be a Tsaponlak, which covers spikes in electronics. The electrically conductive powder is made from a graphite rod of the salt battery. Equal parts of the components are mixed.

The resulting substance is perfect for fixing small parts when repairing household appliances. As a viscous basis, it is possible to apply ordinary nail polish. Such a composition can be easily removed using a solvent when an erroneous application. However, we should not expect good adhesion from the product obtained.

The described compositions can be used to fix the elements that no mechanical impact. To obtain a more durable glue, you need more ingredients.

Production of conductive glue

As an adhesive base, a vinyl chloride copolymer with vinyl acetate is used (CP-430, A-15). It is necessary to connect 35 g of substance with the same amount of silver powder and add 15 g of graphite shredded to dust structure. In glassware, the resulting rash substance must be mixed with 35 ml of acetone. The finished product has a dark gray color and consistency of molasses. The viscosity of the substance can be adjusted using acetone dissolution.

Glue, made according to this recipe, has high electrical conductivity, and its use provides a solid connection of the elements.

Unusual recipe for conductive glue with almost zero resistance! - DRIVE2.

I post for the work of one dude to your honest trial! I want to cook this glue and also to try out - restore 2 heating tracks. I did not change the text and the public from his face.

At first I had a hope to make glue in the traditional way - from the styling of a soft pencil, from the brushes from the electric motor, from the central contact of the salt battery.

But every time I was waiting for disappointment - when drying, the resistance of the adhesive at best was calculated with hundreds.

For one button, it may have passed, but when the whole key field had multiple damage, the result was not difficult to guess.

Googled, like any experienced radio amateur. Yes, silver-based recipes are present on many sites. But the trouble is that I do not have the necessary chemical components and it is almost impossible to get them in Lugansk now.

He began to think than to replace silver. And then I was painted: because the usual copper, there is little worse than silver. It is in many details and resistance to her not much more silver resistance!

In order to get a fine copper conductive dust, I decided to use the diamond circle from the grinding machine.

As a source of copper, there was an eyelet from the recently faced stabilizer 7805. On small speeds of the side surface of the disk in a few minutes, the slide of copper dust was sank.

Began to try different binders to turn copper dust into a conductive path. After several unsuccessful experiments, I found a suitable option - the adhesive "Dragon" for the ceiling tiles.

It is sold in a floor of liter plastic bottles there, where they sell the ceiling tiles and wallpaper. It is not expensive, the glitter is very worthy, so that the farm is useful. Transparent, does not stink.

Before any consistency is easily divorced by ordinary alcohol.

True, due to alcohol, another problem arose - the conductive glue dries too quickly. A little stirring with convolutions, I realized that it was necessary to reduce the surface area of ​​the evaporation of freshly prepared glue.

To do this, made a mini-tube from the segment of the gel handle rod. The thermoclaim knocked him on a piece of plastic from PET bottles. It turned out a steady design.

As a stick-stirrer, it is convenient to use wooden toothpicks - they are smooth and with thin tips. Plus, almost nothing.

Since there were large pieces of laptop on the laptop keyboard, "Shunts" from wires from MHTF-0.07 turned out to be a good version of their recovery. Unfortunately, until the end to bring the keyboard repair of a notebook of a friend, I could not yet - I could not come up with how to glue the "sandwich" - the bottom film with the tracks was glued to the upper special, and thus connected electrically. Contacts are very small and how to combine blindly, without causing closures of neighboring tracks, I have not yet invented. But the tracks of the tracks managed to restore.

Types of conductive glue contact

Contactol is an innovative product of the German chemical Keller concern, which specializes in the manufacture of current and thermal conducting adhesive compositions on a patented recipe.

The glue of this brand is designed for the installation of electronic parts of the microcircuit, restore tracks on printed circuit boards, eliminating breaks on contacts.

To date, the glue contacts is available in three versions:

Glue contact in silver - single-component visco-fluid conductive composition designed to create electrically conductive communications on dielectric bases (glass, textolite, etc.).

The modified resin of synthetic origin is used as a binding element, the conductive filler serves fine silver powder (999 sample). The glue is thermal resistant, has a high covering ability, excellent moisture resistance.

Specific volumetric resistance of the frozen composition is 0.01 ohms per cubic centimeter. Adhesive Contactola is produced in the columns of a volume of 2 grams, costs about 300 rubles.

Radio contact with a completely ready-to-use single-component conductive glue, designed to create conductive communications on glass, plastic and other dielectric bases.

A modified resin is used as a binding basis, a fine graphite powder corresponds to conductive properties. The glue contacting radio is available in miniature plastic flasks (2 grams), costs about 150 rubles.

Covering marker Contactol - glue based on polyvinyl chloride resin and silver powder. Designed for applying electrically conductive tracks, jumpers, etc. The unusual form of a conductive adhesive is significantly facilitated by the process of applying the composition for dielectric bases.

It is enough to intervene a tube and shake several times so that the filler is evenly distributed over the resin. Immediately after that, you can apply a conductive pattern on the panel.

It is rapid enough, and after 5-10 hours (depending on the thickness of the glue), complete polymerization occurs. To accelerate the frost, you can dry the place of application of the hairdryer. The conductive marker is produced in a blister pack 7 gr., It costs about 600-700 rubles.

Video Overview

How to make a conductive glue with your own hands: making recipes

Today to buy in the market the conductive adhesive firms Done, Deal, or other trademarks will not be difficult. However, the cost of it is not small. And if you need a lot of this substance, it will be wiser to think about trying to make this agent yourself.

Therefore, many are resorted to to make a conductive paste or glue for the car on their own. Today it is quite possible to do without excess spending at home, and, and, with the quality composition.

How to prepare homemade nonsense conductive glue:

  1. The universal method designed for the main property of the conductive adhesive is high electrical conductivity. For its manufacture you need to buy the most common transparent Chinese superchalter in tubes. (If the amount of glue you need is large, contact the car shop, where you will find the number of Chinese superclause you need). Next, we take the usual simple pencil, or plates of graphite, and grind the substance into powder making graphite dust from it. Use an unnecessary blender to accelerate the process. But in dust you can turn graphite manually only under the press. Having achieved proportions 1: 1 thoroughly mix ingredients, and your electrically conductive glue or paste is ready. The properties of the superconception after mixing with graphite slightly decrease.
  2. For this recipe, it will be necessary to prepare more ingredients. You will need: powder graphite - 6 g, powder silver - 65. Mix these ingredients and more than them in a step. Then it is necessary to add to the mixture to be obtained: a binder - nitrocellulose in an amount of 4 g, rosin 3 g, ethyl acetate or acetone 25g, all this is thoroughly mixed and overgrown to a homogeneous mass. After a while, this glue thickens, so before applying it is necessary to add acetone. This will give the composition of the necessary viscosity. The glue prepared in this way is simply ideal in the case of the repair of heating of the wind rear window and seats. This is the composition made by their own hands, consider the ideal variant of the conductive glue during car repairs. However, it is possible to apply it only to connect mechanically not loaded auto elements.
  3. This recipe is suitable for those moments when you need to achieve perfect consistency and balance between the reliability of the clutch and the quality of electrical conductivity. For the manufacture of such a miracle composition, a graphite powder, close to dust in the amount of 15 g, vinyl chloride vinyl acetate weighing 30g, silver powder - 35 g, and pure acetone with a capacity of 35 ml. In porcelain or glass tank, we thoroughly mix all the necessary components before receiving the consistency of the black and gray syrup. Before use, glue is well mixed with a durable glass wand. The viscosity of the obtained glue can be adjusted using acetone. To do this, in a porcelain stage, all the available components are pretty. Ready glue Put into glass dishes having a fit plug. This type of glue is great for repairing heating strips on the rear window. This glue is also used in cases where a solid grip and good electrical conductivity is necessary.
  4. To get the composition on this recipe, we need to prepare a chaponolac and a conventional graphite rod from any battery. Grinding the rod to the powder state, then thoroughly mix with the first ingredient before getting a gel consistency. This type of glue is great for repairing household appliances, which has problems with small parts, as well as with flaws in the heating of the rear windscreen car.

All varieties of glue, which carries out electricity, must be stored in glass containers having a neck with a proliferated lid.

Where it is applied

Thermal conducting glue is simply indispensable where it is impossible to use an electric staircase, otherwise the threat of the deformation of the microcircuit increases. Some details are so miniature and elegant that the sting of the soldering iron is superior to the sizes of the surface, so its application is impossible.

Cleaning adhesive has a wide scope of application:

  • Prints of heating threads on the back or front of the car;
  • connects piezoceramic plates in radio devices;
  • It is used if two dielectrics connect to which communication will be held;
  • for cold spikes;
  • For solder postings of small sections, which cannot be connected by a hot method;
  • joins the torn paths of the remote control, keyboard, etc.;
  • is the basis for paint or enamel with conductive properties;
  • In the repair of computers, mobile devices and other high-tech equipment is used to attach crystals and microcircuits to the board;
  • restores the conduction on damaged areas (buttons of the TV from the TV, keyboard;
  • when installing electrical heating systems ("Warm floor" system);

The means of contacting is used in the manufacture of own printed circuit boards, when repairing the rear window heating tokens, connecting the wires by the method of cold soldering. Silver-based glue has a high viscosity, is actively used in the process of repairing radio equipment and computers.

Done deal glue is a double, one syringe has an adhesive basis, the other is conductive. Actitically used in the repair of the heating system of the car.

Homakoll is a conductive base that the heating awning is laid out. This is also an excellent antiseptic, as well as a thermal insulator. Used for the device "Warm floor" system.

Industrial adhesive TPK-ue means withstands the temperature differences from -190c to + 200C. Perfectly connects electrically conductive elements even to a steel surface, without losing technical characteristics. Bashes aluminum alloys, glass and carbon fiber.

Famous trademarks

There are not many brands from manufacturers of conductive glue on the market. These include both Russian companies and foreign. Below we list the most proven brands of adhesive substances:

  1. The brand of glue conductive contact with silver 2g is designed to create highly elastic durable surfaces. It is performed on the basis of silver. It is distinguished by fast dried rates, thanks to which it is convenient for work. You can buy "Contactol" in any radio logs or market. However, it should be noted that most of the reviews about this brand are negative.
  2. Elekton is a conductive composition based on epoxy resin, often used by motorists. Reviews of this product are also far from always positive.
  3. Adhesive "Done Deal" of foreign production. "Done Deal" is characterized by high strength and reliability. This brand has good reviews from professionals.
  4. Homakoll is a popular brand of conductive substance, which has long been in the market. Most often applies as conductive glue for linoleum by large manufacturers. It has antistatic qualities.
  5. "Mastix" - electrically conductive lubricant for repair work with rear glass of the car. "Mastix" is considered the best choice in its segment.
  6. TPK-E is a brand of glue from the Russian manufacturer. The feature of the composition is the ability to maintain operational characteristics with a wide temperature variation - from minus 190 to plus 200 degrees Celsius. Most often, this brand is used in industrial conditions.

Features and properties

Before use, you need to carefully study the composition of the adhesive and not to use the means containing water. The composition and application instructions are indicated on the factory packaging of glue. For microcircuits, wires of wires, loops, other elements of electrical engineering, the water base is destructive. This composition will dry out for a very long time.

The component transmitting the current in the glue is often graphite or nickel powder, silver or any other metal. The greater the content of the electrically conductive component, the worse the adhesive hitch with the surface.

  • can be repaired computer loops, microcircuits;
  • used when installing heating plinths;
  • It is used as glue for linoleum when the antistatic flooring is placed;
  • Defects are eliminated in the automotive electrician, rear window heating is repaired;
  • Piezoelements are bonded in radio equipment;
  • Used when replacing the soldering of light-emitting diodes.

Composition of conductive glue

Another feature of this glue, which is mentioned in much less, is such a concept as drying. For perfect solutions, sinking at one point.

Instant drying for conductive compositions is mandatory. With a diverse, the work of the master slows down. In addition, areas can suffer on chips, which will sing with these glue, if it is liquid and is not localized in the same segment.

The composition of the conductive glue, made in accordance with the technology for better conductivity, present the following elements:

The news about this at one time pushed some of the idea of ​​the melt of unsuitable chip and extraction of valuables. However, their presence in the elements is so little that, from this undertaking, enterprising gold killers had to abandon. In addition to its basic gluing functions, conductive glue is obliged to have a very high security indicator and for the environment, and for the master itself.

Electrically conductive glue: what is it and where is used

Conducting glue can be easily called a universal substance that is used in almost all spheres of mechanical engineering.

Due to the heat resistance, the conductive glue is used in the repairs of various heating mechanisms, as well as with the arrangement of the warm floor and tile system.

Where the conductive glue or paint is used:

  • In the manufacture and repair of computer and household appliances, consoles, loops, tracks in the keyboard board;
  • It is with the help of it that the fees and chips are revealed;
  • Apply when installing heating systems and heat inlet and heating plinth;
  • It is indispensable in the process of repairing machines;
  • Sometimes it is used at home instead of soldering for products from metal;
  • During nail extension;
  • It is used as a sealant for elements when arranging the heating of the rear windscreen and during the repair of heating threads.

In the electrician, such a composition of the adhesive is especially needed. It is practically nothing to replace it, and sometimes without it is simply impossible to do. In addition to glue conductive, there may be spray, paste, varnish and marker.

How to make a conductive glue on a silver basis

To do without these problems when working with non-ferrous metal, it is possible to make a conductive cream on silver, but it is much more complicated than working with pencil trap. Before starting work, it is necessary to acquire nitric acid silver, but it can be more difficult than replacing it with nitric acid; It also carries out electricity.

The pharmacy needs to buy a 1% solution of formalin and a bottle of ammonia (ammonia alcohol).

Mastering equal proportions carefully, you need to mix formalin and nitrogen acid silver to begin with, then add a couple of ammonia drops to the resulting mixture.

If the actions were made without errors, after some time the resulting composition drops a black precipitate - silver powder, which must be obtained from the liquid (you can use distilled water or filter) and used for electrical conductivity purposes. Next, a peasant of the extracted precipitate extracted from liquid at a high temperature of 105-150 degrees Celsius. The resulting dried black powder should be added to a similar prescription any quick-drying glue. Professionals are advised first to mix glue with a small amount of alcohol. Due to the high speed of the composition of the composition, it requires periodic stirring.

There are a huge set of such recipes, but they are all based on the same processes. It is enough to remember the lessons of chemistry or physics in school to highlight which elements are conducted, and later on their basis, prepare an ideal glue paste for the product.

Preparation of silver powder for the manufacture of conductive glue

To obtain powder silver we will need:

  • Silver
  • Nitric acid
  • Soda
  • Formalin (1% solution)
  • Summer alcohol (5% solution)

First we dissolve silver in nitric acid as a result we obtain nitric acid silver (LAPIS)

I think it will not be superfluous to say that with nitric acid you need to treat special caution, in order not to get strong burns

Currently, each apartment has devices operating from electricity. There are large appliances appliances, and there are very small like remote from the TV or clock. All of them have long become part of everyday life, and without them it is difficult to present the usual state of affairs in everyday life. Each device can break.

Many radio amateurs, and simple electrical appliance users, in the process of repairing devices, face the need to preserve conductive glue, varnish, gel or lubrication for contacts. In principle, the electrically conductive glue can be purchased in radio electronics stores, experts already know about the presence of so-called contactola. At the same time, it's not so easy to find it. Sometimes you have to look for a long time and wasted that there are nerves and strength.

Such conductive glue, varnish, gel or lubrication can be made with your own hands. How to make it home? The main thing is that there is nothing complicated. It should be aware that the composition of most such adhesives contains certain binders. These include the following: polyurethane, polyester, epoxy and others. Conductive metal powders are added to these substances: silver plated, silver, gold.

When preparing a conductive glue, you can adjust its consistency. This is achieved by adding the glue of certain solvents - isopropyl alcohol, acetone, ethyl cellosolva. And also to create such an adhesive, you can see various videos for a better understanding.

To begin with, it is necessary to list the components that will need to be used in the process of producing powder silver:

  • silver;
  • nitrogen acid;
  • Summer alcohol (5% solution);
  • soda;
  • Formalin (solution 1%).

To begin with, it will be necessary to dissolve silver in nitric acid. At the output is a nitric acid silver

It is worth noting the fact that work with nitric acid involves compliance with caution and accuracy, as as a result of careless actions with this substance, you can get serious burns

After heating into the solution, several drops of pre-pre-pre-ammonia alcohol are dripping. As a result of the indicated manipulations, a dark sediment is formed. It will be necessary to rinse with distilled water, and then add. The temperature of the drowsh should be approximately 110 degrees.

Radio amateurs more often than others have to deal with electric shock, and the current in turn is very elected in terms of the compositions by which it should pass. The electrically conductive glue acts in this case with a real salvation, and it is it that is used for electricity, useful for its skill to spend current.

The glue can be used to work with electrical circuits (for example, in keyboards or consumer electronics), when creating heating and flooring tools. But not only radio amateurs it will be interesting. This type of glue is truly necessary when repairing cars: it is used with glass, as a conductive paste for sealing, etc. Consider more, how to make a conductive glue with your own hands and how can it be replaced.

Features and properties of conductive adhesive compositions

For the first time, electrically conductive glue was done in Germany in 1940. Later it began to be actively used in different areas of mechanical engineering, and now it is considered to be a universal means. Real conductive glue can be used instead of soldering, for the arrangement of warm floors, heating systems: it perfectly withstands the temperature raising. Other properties of the means are as follows:

  • Quick speed of drying, the need for work without pauses;
  • high viscosity (eliminating the impression of glue inside the power supply);
  • excellent adhesion with surfaces;
  • security for the environment and user;
  • Elasticity (makes it possible to dot applying).

The main property of glue is its low electrical resistance. The use of electrically conductive adhesive helps to give parts stability to damage, shocks, vibrations. Also, the composition will protect the chips from temperature drops.

It is important that the glue for electronics does not have water in the composition. The water base will only spoil the electrical circuits, the contacts of the wires, and the tool itself will dry too long

Typically, nickel or graphite powder, silver or any other metallic, conductive current, are included.

The applications of conductive adhesives are diverse:

  • Repair of loops, computers, gadgets;
  • Installation of heating plinths;
  • laying of antistatic linoleum;
  • Elimination of electrician defects in auto, application for repairing rear window heating, heating threads;
  • Replacing soldering LEDs.

How to make conductive glue at home

There are several recipes for cooking a conductive adhesive with their own hands.

Recipe 1: Second Clay + Simple Pencil

  1. We take any cyanoacrylate glue (the so-called super-adhesive) in a metal tube, add graphite powder into it in a ratio of 1 to 1 and stir up to the formation of a homogeneous consistency.
  2. For convenience, you can prepare glue directly in the tube.
  3. To do this, it is gently unfolded from the end, the powder is added, stirred by a match or toothpick and turn back again.
  4. The desired amount of graphite powder can be easily obtained by grinding the rod of the most conventional simple pencil with the blade, appliance or sandpaper.

Recipe 2: Battery + Tsaponlak

For this recipe, you need a conventional salt finger battery, more precisely the battery itself, and the graphite rod from it.

  1. Graphite is crushed and mixed with a Tsaponlak in equal proportions.
  2. Tsaponlak is a clear solution that is used in radio electronics for coating soldered electrical connections. You can purchase it in the store for radio amateurs, a glass bottle of 30 ml is worth about 50 rubles.
  3. You can prepare glue directly in the bottle, it can also be stored for a long time.

Recipe 3: Epoxy + Aluminum Powder

Conductive adhesive can also be prepared based on epoxy resin.

  1. For this, the cheapest two-component glue of the brand EPD of domestic production is suitable (costs about 150-200 rubles for 280 gr.).
  2. Aluminum powder is usually used as a conductive filler.
  3. The preparation recipe is simple: the resin is stirred with aluminum powder to a state of thick sour cream. Immediately before gluing, the prepared composition is stirred with a hardener in a ratio of 10: 1.
  1. In the porcelain level, powder graphite and silver, copolymer of vinyl chloride vinyl acetate and acetone are carefully laid.
  2. You need any ordinary nail polish.
  3. Next, you can pour crumb varnish and mix for example a match.
  4. The result is a black and gray liquid, similar to consistency on syrup.
  5. It is necessary to store it in glass dishes under a tightly closing lid.
  6. Before each use, glue is stirred.
  7. On the product he dries about fifteen minutes.

VIDEO INSTRUCTION

https://youtube.com/watch?v=u2YLW5Ru0fu.

All listed recipes allow you to quickly and with minimal cost to prepare glue at home, which is suitable for repairing the threads of the rear window of the car and solving other tasks.

An important point: the greater the conductive filler will be in the adhesive solution, the better there will be a conduit, but the strength of the connection will inevitably decrease.

Consider the use of conductive adhesive on the example of repairing the heating of the autoglass:

  • The break point is wiped with a solvent;
  • We glue the tape from above and below the thin thread;
  • Apply the adhesive composition to the place of the break;
  • After complete drying of the glue, we remove the scotch.

High-quality conductive glue ensures the passage of electric current with normalized losses. Such formulations are used to restore printed circuit board tracks, other repair activities. This publication discusses factory products and functional analogs that can be made independently at home.

Additional options

Less frequently users try to make other types of glue, which serve as an alternative to store products.

Glue stick

Adhesive pencil make from PVA. For the case you need to take the old packaging from a deodorant antiperspirant, which is tightly closed. Senthing the economic soap (2 parts), pour water (1 part). Dissolve in a water bath, pour 4 spoons of PVA, cool. After laying out a lot of packaging, give to frozen.

Super glue

This super-glue make, of course, will not work - it is prepared from cyanacrylate with the addition of a number of complex chemical components. But a very reliable composition still can be created with your own hands. To do this, you will need:

  • 125 g of joinery glue;
  • 100 g of sugar;
  • 35 g of hazed lime;
  • 450 ml of water.

Sugar is dissolved in water, they add lime, heated 30 minutes in a water bath. Next into the solution is placed with chopped carpentry glue, boil until the mass is homogeneous. The remedy can be used to glue the metal, ceramics, porcelain.

Glue for foam

It is best for sticking foam fitting joinery. Casein glue is also suitable, which is mixed in equal parts with haired lime. Such a means is ideal for fastening foam in the insulation of the house.

Glue made of foam

From acetone and foam plastic make glue for connecting elements from glass, metal, wood. The foam is crushed into the crumb, poured acetone to completely cover it. Pulling mass is almost immediately, it can be used as ordinary glue, simply mixed.

In the manufacture of adhesives, you can seriously save, especially if in the house, the apartment is planned to be great repairs. The quality of the finished product can give up a slightly selling, but it will definitely be safe for health and accessible!

Today, in order to restore the track on the board or assemble a homemade electrical appliance, it is often used by specialized conductive glue called Contactol. Of course, its price is not so high and is about 200 rubles, but what to do if it is not common in the nearest stores, or you need it literally a little bit to restore the track, for example, on the board. On the Internet, you can find tips on the independent manufacture of such a product from graphite and glue or varnish. In this article, I will check whether such a varnish is really working.

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

List of essential material

So, for the manufacture of homemade conductive glue, we will need:

1. Graphite pencil (soft or especially soft), it is also possible to use graphite rods from spent batteries, and ideally copper-graphite brushes with electrical appliances.

krsk.au.ru.
krsk.au.ru.

2. Glue either varnish, is suitable absolutely everything that you have in stock.

3. Passatia.

All components are prepared, it means quite possible to move to production.

We make conductive glue (varnish)

To do this, remove a graphite rod from our pencil, then grind it into powder, and the smaller, the better.

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

Then if you decide to use super glue, then take a tube and carefully unfold it, as shown in the photo:

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

Then in the already opened tube we fall asleep our graphite powder, and the powder ratio and glue should be one to one.

Next, we need to mix our conductive glue, for this you should take a big needle (you can do the toothpick or match) and mix thoroughly.

And then we close the tube and reliably clamp the connection with the passats.

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

Everything, our conductive glue is ready to use.

If you use varnish as the basis, the production process looks like the same. Only I recommend finding a small container with a tightly closing lid, into which you put the right amount of varnish and already directly in this container mix graphite and varnish.

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work
Note. If the conductive lacquer is a bit snack, then it can be completely dissolved by a solvent and use again for its intended purpose. But such a focus with the superclaim will not pass.

Checking performance

So, our mixture is ready, now let's check how it works. I preferred a mixture of varnish and graphite, because in my opinion, in my opinion, it's easier to work with varnish, although it will dry longer than glue.

I decided to connect the contacts of the LED tape using a conductive glue and ship it from the crown. And that's what I did.

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

How do you see the second half of the LED tape connected via conductive glue, does not light up. And that's why:

We make conductive glue (lacquer) with graphite and check its work
We make conductive glue (lacquer) with graphite and check its work

Varnish (glue) mixed with graphite really restored the chain, but in the place of application of the mixture, a transition resistance was formed (therefore the LEDs were not lit).

Conclusion

Of course, this method of connection will not replace the soldering, but repair, for example, the track on the keyboard or other microcircuit is quite possible. It is also necessary to consider that when current flowing in this place, heating will be carried out and quite significant.

And to reduce resistance to this conductive lacquer (glue), it is desirable to add powdered copper or silver.

Otherwise, this is a completely efficient version of the replacement of contactola.

If the article turned out to be interesting to you or useful, then appreciate it like and share it in social networks. Thank you for your attention!

I post to review the work of one dude to your honest court! I want to cook this glue and also to try out - restore 2 heating tracks. I didn't change the text and public from his face. I had a hope of making glue in a traditional way - Soft Gulf Pencil, from the brushes from the electric motor, from the central contact of the salt battery. But every time I was waiting for disappointment - when drying, the resistance of the adhesive at best was calculated with hundreds. For one button, it may have passed, but when the whole key field had multiple damage, the result was not difficult to guess.

Googled, like any experienced radio amateur. Yes, silver-based recipes are present on many sites. But the trouble is that I do not have the necessary chemical components and it is almost impossible to get them in Lugansk now.

He began to think than to replace silver. And then I was painted: because the usual copper, there is little worse than silver. It is in many details and resistance to her not much more silver resistance!

In order to get a fine copper conductive dust, I decided to use the diamond circle from the grinding machine.

As a source of copper, there was an eyelet from the recently faced stabilizer 7805. On small speeds of the side surface of the disk in a few minutes, the slide of copper dust was sank.

Began to try different binders to turn copper dust into a conductive path. After several unsuccessful experiments, we found a suitable option - the adhesive "Dragon" for the ceiling tiles. It is sold in a floor of liter plastic bottles there, where they sell the ceiling tiles and wallpaper. It is not expensive, the glitter is very worthy, so that the farm is useful. Transparent, does not stink. Before any consistency is easily divorced by ordinary alcohol.

True, due to alcohol, another problem arose - the conductive glue dries too quickly. A little stirring with convolutions, I realized that it was necessary to reduce the surface area of ​​the evaporation of freshly prepared glue. To do this, made a mini-tube from the segment of the gel handle rod. The thermoclaim knocked him on a piece of plastic from PET bottles. It turned out a steady design. As a stick-stirrer, it is convenient to use wooden toothpicks - they are smooth and with thin tips. Plus, almost nothing.

Since there were big pieces of laptops on the laptop keyboard, "Shunts" from Westers from MHTF-0.07 turned out to be a good version of their recovery.

Unfortunately, I haven't succeeded before the end of bringing the keyboard repair of the keyboard - I was not able to come up with how to glue the "sandwich" - the lower film with the tracks was glued to the upper special and thus connected electrically. Contacts are very small and how to combine blindly, without causing closures of neighboring tracks, I have not yet invented. But the tracks of the tracks managed to restore. Source: SmartElectronix.biz/Publ/..._SOPROTIVLENIEM/11-1-0-117

Conductive glue, a few good recipes. The use of such adhesive as a heat-conducting

Conductive glue, a few good recipes. The use of such adhesive as a heat-conductingThere are situations when you need to quickly repair electrical contacts. At the same time, wires, solder, rosin, soldering iron or the more sockets are not. In such emergency situations, the conductive glue can save. Do not reduce the role of that contact glue. Personally, I tried to create schemes with radio components completely performed without a soldering iron and solder, but only with the help of conductive glue, the result is surprisingly good. In designing boards with glue, I recommend using different conductive abilities and density. Sometimes with glue on the board, it is possible to make even resistance or not a big capacitor, not to mention different coils, arresters, antennas, conductive labyrinths and patterns, there are many spaces for creativity. Cut all such a scalpel on the copper foil board, or to ride it in a solution is more difficult, and it will take more time, you can not always find a fee with a copper foil. Motorists conductive glue can be useful when repairing a car rear glass heater. Conductive adhesive manufacturer recipes: 1) "Durable" Cooking dishes It is advisable to take a glass. Take graphite, it is possible from the rod of a pencil or old engine brushes, we carry it into a fine powder, can be small supfyl, about 15% (by weight, from the entire composition of the future glue), Also, it is also necessary to flick into the powder a piece of silver 30%, Copolymer vinyl chloride vinyl acetate 30%, acetone 30%. Thoroughly stirring with a glass stick. The glue must be stored in glassware with a fitting plug. Such a composition can be used where strong compounds are needed, but there are no greater electrical conductivity requirements. 2) "WITH R'NIFOL" Graphite powder 5%, silver powder 50%, nitrocellulose 4%, rosin 3%, acetone 30%. All components are mixed and rub to uniformity. Before applying glue should also be mixed. To obtain the desired viscosity, add acetone. 3) "on alcohol" Powder Silver 50%, Powder Graphite 5%, Schellack Natural 3%, Ethyl alcohol 30%. Mix well and also stored in a glass jar with a fitting plug. The shellated recipe is more often used where the glued contacts are not loaded mechanically. 4) "Copper Glue" Clay can also be made with fine copper chips. Take a piece of copper and erect it in fine powder with a small file, copper it is necessary to 60%. Add graphite powder 30%. Powders are gently mixed. As a binding agent, take varnish. By adding stirring lacker, we obtain the glue consistency you need. 5) "Graphite Glue" Well, if you just just take ordinary glue for rubber. By adding a graphite powder mixing to obtain the desired glue density. Do not forget that with a large number of graphite, glue has good electrical conductivity, at the same time it is more dense. 6) "Small Silver" If it is difficult, it is necessary to produce nitric acid silver, a solution of formalin 1%, aimia solution (alcohol is ammonia). We mix equal portions of formalin and nitric acid silver, after which add a few drops of ammonia to add there. There should be a black precipitate, it is silver powder. Such powder can be reached with a solution, rinse with water, dry and add to the glue that dries quickly. Glue first not bad sensitive to solve solvent (more often alcohol or acetone) Then add silver powder. The property of this method is that the powder silver is very fine, respectively, the glue turns out to be more conductive. According to the idea, the conductive glue can be partially used as heat-conducting. After all, almost all well-conductive metals are well carried out and warm. But for example, the diamond is well carried out warmly but almost does not spend the current. Diamond can sometimes be a semiconductor, well, until the semiconductor paste we do, but in the future, perhaps. In industrial thermal conducting pastes and glues, small powders of metals are also used, diamond dust. The thermal conducting paste often does not have mechanical strength and does not hold the item. Therefore, to create both strength and current and heat conductive features can be used conductive adhesives. If anyone has recipes of conductive adhesives, heat-conducting pastes that spend or do not conduct a current, write.

With the development of electronics, the microcircuits ceased to be rare and moved from scientific laboratories, literally, in each house. They served systems for heating windows in auto, television remote, computer keyboard, etc. Like the whole technique, they fail, but not every breakdown - the reason to go to the workshop and pay for the repair.

Minor malfunctions of the type of disconnecting contact in the television remote from the TV can be corrected by having a special glue at hand. It is sold in household appliances stores, but its cheap analogue can be prepared at home. Today I will answer questions: what components are needed for this and how much they need them, for which it can be useful made by your hands conductive glue.

What is a conductive glue?

Conducting is called glue transmitting electric current. The electrical conductivity of this class of materials is achieved by adding a conductive component to their composition. Silver, gold, palladium, nickel, copper or graphite are used as such a filler. They are mixed with one of the adhesives: varnish, silicone or synthetic resin.

The most popular component is silver. It spends the current well and is cheaper than gold, so most electrical types of adhesive make with it. Some brands contain not one supplement in its pure form, and their mixture, for example, silver with copper or silver with graphite. This reduces the cost of glue. By the method of polymerization, all conductive adhesives are divided into self-measuring, thermal curing and light-cured UV adhesives.

Where is electrically conductive glue?

The objectives of using electrically conductive adhesives can be divided into two large categories. The first is a conducting use when the adhesive tracks replace the wires, the second is shielding. The compositions of the conductive adhesives for electronics are made on the basis of metals, and for shielding materials, mixtures with graphite are often used.

Scope:

  • manufacture of semiconductors, printed circuit boards and electronic microcircuits;
  • Grounding the sample in scanning electron microscopy;
  • the creation of electrical contact between the elements that cannot be soldered;
  • painting the inner surface of the housings containing electronic devices in order to protect them from electromagnetic radiation;
  • Fixation of antistatic linoleum and other conductive coatings.

Popular ready-made brands

The finished means of this group have specified viscosity and electrical resistance parameters. The electrically conductive particles are structured in them by an electromagnetic field, which improves the technical characteristics of the materials. The most popular brands of current adhesives: "Contactall", "Circuit Loctite 3863", "Permatex PR-21351", "Mastix", "Homacoll 168 EL PROF", Irpol 5.

German electrically conductive glue »Contactol» produced in several versions:

  • one-component "contactol" on silver;
  • Composition "Radio Control" on graphite powder;
  • Conductive marker "Contactol" on silver and palladium.

One-component "contactol" is a mixture of fine powdered silver and synthetic resin. If necessary, this glue can be diluted with acetone, isopropyl alcohol or cyclohexanone, making it less viscous. It sticks well to metal, glass and plastic. Included with glue there is a brush for applying it. Packaging "Contactola" Weight 10 g costs 220 rubles.

"Circuit Loctite 3863" - glue for repairing the rear window of the car rear window. A set of accessories is attached to the adhesive: a stencil with a protective film and a bruster for applying. The composition is suitable for working with ceramics, rigid plastic, glass and metal. They can eliminate defects with a length of up to 10 cm. The glue is recommended to apply in three layers with 5-minute intervals. Stencil is removed after half an hour. You can use the heating circuit through a day after repair. Packing cost weighing 2 g - from 900 rubles.

"Permatex PR-21351" is a conductive adhesive for fixing and repairing the threads of heating the rear window of the car, the loops of the display of a smartphone or tablet, and others. The glue is attached with a napkin with an activator to wipe the surface before gluing. Tube with 11 g glue costs from 311 rubles.

Mastix contains nickel powder. According to the strength of sticking to the metal, it competes with cold welding. It is used to fix and restore contacts in the heating threads of the rear windows. The remedy is suitable for the repair of contacts with the length of the gap to 2 cm. The glue package of 55 g costs about 80 rubles.

"Homacoll 168 EL PROF" is a glue that fixes antistatic coatings to the floor or walls. Such coatings are needed in rooms with a large number of electronics: server rooms, assembly halls of accurate devices, electrophysitherapy offices. Electrically conductive glue has an shielding effect and protects the devices from the accumulation of electrostatic charge on their body or surface on which electronic elements are installed. This adhesive does not contain combustible or toxic components, so they can be glued with linoleum in closed residential premises. The cost of 10 kg is about 4400 rubles.

"Irpol 5" based on polyurethane. It is used to glue outdoor coatings. Protects surfaces from static electricity accumulation. Cost 1 kg - from 100 rubles.

How do you make glue, conducting electricity?

If we are talking about the repair of complex electronics, it is better not to save glue on the purchase of glue. Materials manufacturing materials have accurate viscosity, electrical conductivity, drying rates and strength after polymerization. They are difficult to replace their own manufacture. However, the homemade adhesives have its own niche of the application: they will be outlined in the case of urgent repair of small damage in contacts, and also serve as training material for work in the domestic workshop or school mug of young technicians.

The homemade analogue of the finished glue can be made with their own hands from inexpensive and affordable materials that are easy to find or buy in the nearest store. You only need to follow the instructions for the manufacture of adhesive at home.

Fast-drying glue (varnish) and graphite

The main advantage of graphite varnish is that all the components needed to make it in every home. The recipe for the manufacturer of the conductive lacquer with their own hands is extremely simple: finely crushed graphite powder mixed with a semi-liquid base. As a binder agent, you can use cyanoacrylate superclauses "moment" in tubes, colorless nitroquac, a tsaponlak or ordinary nail polish. Do not use colored varnishes, because they have pigment impurities that can reduce the electrically conductive properties of the mixture of the mixture.

As a source of graphite, you can take graphite (ordinary) medium softness or soft pencils. You should first check them with the tester and make sure that their core is made of graphite, does not contain additives and really conducts current.

Graphite powder

Another source of graphite is used batteries or copper brushes. The graphite rod is crushed with a sharp blade into powder. After receiving the desired amount of material in it, you should add the basis to it to dissolve with graphite to the state of the casis. The optimal ratio of powder and liquid is 4: 1. It follows to work quickly, because varnish dries quickly.

If superclauses are used as a solvent, the ingredients are mixed directly in the tube, printing it from the opposite side. Then the edge of the tube is again carefully closed and the resulting mass is squeezed to the sections intended for this through a narrow hole in the nose. This method is very convenient, since in this case, glue is preserved in a liquid state, it is easier to apply and not dirty hands.

Based on silver

Silver-based glue conducts electric current better graphite. The following components will be needed for silver:

  • Silver nitrate solution;
  • Formalin 1%;
  • Summer alcohol 5%.

Silver nitrogen solutions and ammonia are mixed in proportion 1: 1. Then the mixture is added dropwise. As a result of the chemical reaction, the restored silver falls into the sediment. It is filtered from the liquid, dried with warm air and mixed with glue or varnish. Electrically conductive glue is ready.

Aluminum powder and epoxy glue (resins)

Glue of good quality can be made from fine aluminum and epoxy resin powder. Aluminum can be molded from a piece of thick wire, an unnecessary aluminum line, spoons or forks. In contrast to graphite, aluminum is crushed not with a blade, but by means of hacksaw for metal or cutters. At the first stage, aluminum powder is mixed with a resin to the consistency of sour cream, without adding a hardener. Due to this, the glue does not dry, but remains liquid.

The catalyst is added directly before work. This glue, in contrast to the two previous two, you can prepare the future, and then split it into small portions and mix the hardener gradually. It is very convenient with a large amount of work requiring time.

I hope the material presented is quite enough to make a conductive glue on your own at home. The following video will complement information.

Добавить комментарий